Showing results: 46 - 60 of 114 items found.
-
Shanghai Guantu Technology Co., Ltd.
The surge current generator is mainly used for surge tests on surge arrester resistors, varistors, discharge tubes, SPD and other anti-surge protection devices and circuits.Inrush current generator ICG-820A series (desktop) meets IEC61008, IEC61009, I61051/61643, ANSI C62.31, C62.33, C62.35, TU K20, K21, K44, K45, UL943 and other standards.
-
Shanghai Guantu Technology Co., Ltd.
The high (medium) voltage TOV tester is used for transient overvoltage tests caused by faults in high and medium voltage systems such as surge protectors (SPDs), and can also be used for other scientific research tests.standardGB/T 16927-1997 High voltage test technology.GB18802.1-2011 Surge protective device (SPD) for low-voltage power distribution system Part: Performance requirements and test methods.IEC61643-1:2005 (Surge protective devices connected to low-voltage power distribution systems part 1: Performance requirements and testing methods)TOV fault test equipment1. Three-phase isolation test transformer2. Single-phase test transformer3. Low voltage switchgear4. Power controller5. Test voltage and current measurement6. Sample box
-
KT-905D -
Kast Eng Co. LTD.
Surge Tester of KAST is divided for the use of 3¡40 §Ç by output voltage, and subdivided into type C of manual decision type, type A of auto decision type, type L of exclusive use for low inductance product test and type P loading printer which can printout its wave form and digital scope. Surge test requires only 0.5 second. Because Surge tester already performs 30 times of Impulse voltage test only for 0.5 second. Turn-to-turn short : phenomenon shorted between the side coils.
-
(SST) 450 -
ATSI
The ATSI SST-450 Surge Suppressor Tester is designed to quickly and easily test allcommonly used transient voltage suppressors: metal-oxide varistors (MOVs), gas-discharge tubes (GDTs), silicon avalanche diodes (SADs), thyristor surge protective devices (TSPDs), and hybrid devices.
-
Fivestar HV Testing Equipment Co., Ltd.
Impulse current test systems are mainly used for testing transmission and distribution systems against the effects of direct or indirect lightning strokes or against electromagnetic interference effects. Primary application of impulse current test systems is the testing of surge arresters, nowadays mainly of the metal-oxide type (MOA) and surge protection devices (SPD). Now they are also widely used to test vehicles, aircrafts, and military applications.
-
SPM -
PJ Electronics, Inc.
High Frequency Digital Surge Tester and DC Hi-Pot Tester (similar to the "SP" Model) together in a compact cabinet. Take this portable tester to your test site and accurately perform Surge, Hi-Pot, PI and Resistance Tests.
-
D-3KAT -
Jabbals
The Digital Armature Surge Tester with bar-to-bar test is a cost-effective solution to check the quality of Small to Large range of DC Traction Motors ideally suited for Railways. The Bar-To-Bar Test is provided to test the Low impedance of the Series wound Armatures and Field coils of DC Traction Motors. The Surge Tester has an Embedded Industrial PC with 8 inch Touch screen Display and software to Store, Recall and Print the Test Reports.
-
DZ800 -
Shanghai Aoboor Electric Co., Ltd.
Insulation resistance, HIPOT, coil DC resistance, turn to turn surge tests can be automatically completed in one time. Applicable to electrical performance test of solenoid valves, changeover valves
-
SGTEL-168 -
Com-Power Corporation
The SGTEL-168 is a versatile surge generator designed to simulate all the environmental surge transients as described in FCC TIA-968-B (formerly known as Part 68) and Industry Canada CS03 standard. It provides a single box solution Type A, Type B (metallic and longitudinal) and Powerline surges. These surges simulate the effect of lightning on telecom equipment under test. So it is also referred to as Lightning Simulator. The electromagnetic energy from the lightning couples into the equipment by powerline or telecom cable exposed to the lightning directly or indirectly. This model is an upgraded version of SG-168 with windows software control and a user friendly front panel for manual operation.
-
HVST -
Test Electronics
The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. This voltage is displayed on an oscilloscope and recorded on the Pass/ Fail LED latch monitor. This voltage will be accurate despite the impedance of the winding being tested. The insulation system can be tested way above the operating voltage because of the brief duration of the applied voltage test pulse. This allows faults to be detected long before they become apparent at operating conditions.
-
SKS-0510I -
Shanghai Sanki Electronic Industries Co., Ltd.
The lightning surge generator SKS-0510I fully complies with the new standards of IEC61000-4-5, EN61000-4-5 and GB/T17626.5; it provides pulse test voltages up to 10kV, which can meet the severity levels of various product standards; Covers the two surge waveforms specified in the standard 1.2/50ms (short-circuit current is 8/20μs) and 10/700ms (short-circuit current is 5/320μs), and a variety of internal resistances are built-in for customer use; Two kinds of surge waveforms, and built-in a variety of internal resistances for customers to use; AC and DC samples can be tested, the rated current can reach 32A.
-
TC Model -
PJ Electronics, Inc.
(Surge with 3 Phase Transfer Switch Consoles) Although all PJ Surge Testers are capable of testing 3 Phase Motors, this "TC" Model has the same characteristics as the "C" Model, but includes a Built-in 3 Phase Test Selector Switch that facilitates 3 phase motor testing by mechanically re-positioning the ground terminal.
-
ETL-15 -
Kharkovenergopribor Ltd.
ETL-15 is compact enough to be mounted even in a minivan, yet contains all the equipment typically found in a fully-featured cable test and fault location system, including burn module, surge wave generator, time-domain reflectometer and high-voltage DC test module.
-
CCS600 -
Suzhou 3ctest Electronic Co.,Ltd.
CCS600 designed as a modular system is the most intelligent solution offering exactly what people need for full-compliant immunity tests against transient, surge and voltage dips. The max voltage is up to 6kV.
-
MIG12100 -
EMC Partner AG
MIG12100 is a current generator with wave shape 8/20 ìs. The exact waveform delivered is a function of the surge generator and the impedance to which the surge is applied. The generator can deliver up to 100kA impulse current supported by 12kV impulse voltage, making it ideal for testing big varistors with high hold-on voltage. Mechanically the MIG12100 consists of two large racks and a separate control console with high voltage output terminals protected by a glass acrylic test cabinet.